정보가 곧 파워입니다. 팀 Sunweb의 도움으로 설계된 신형 NeosTrack GPS Cycling Computer는 한계를 이겨내기 위해 필요한 정보를 라이더에게 제공합니다. 통합 FTP/LTHR 테스트 프로토콜, 자동 동기화 및 턴 바이 턴 경로 안내 기능을 갖춘 NeosTrack은 작은 크기이지만 필수적인 라이딩 파트너입니다. NeosTrack은 한 번의 충전으로 최대 33시간의 배터리 수명을 자랑하며 Bluetooth 기술로 스마트폰과 원활하게 연결됩니다. 또한 대부분의 ANT+ 파워미터 및 트레이닝 센서와의 호환성을 위해 ANT+ 기술을 탑재하고 있다.
2.6인치 LCD 디스플레이
긴 배터리 수명: 최대 33시간
빠른 시작: 고감도 GPS 수신기가 신속하게 위치 정보 확인
쉬운 설치: 5개의 물리 버튼과 직관적인 UI로 간편하게 조작
자동 동기화: Wi-Fi를 통해 STRAVA 또는 TrainingPeak에 자동 업로드 지원
배터리 지속 시간: GPS 절전 모드 최대 33시간, GPS 풀 파워 모드 최대 27시간
IPX 7 방수 성능
대응 무선 방식: Bluetooth SMART 4.0 (스마트폰 연결), ANT+ (각종 센서 연결), 무선 LAN (데이터 동기화)
과학적인 훈련은 라이더의 실력을 효과적으로 향상시킵니다. GIANT NeosTrack GPS 속도계는 전문적인 사이클리스트를 위한 최상급 훈련 데이터부터 초급 라이더를 위한 기본적인 주행 정보까지 다양한 정보를 제공합니다. 또한 주요 트레이닝 데이터에 즉각적으로 접근할 수 있어 자전거 위에서의 퍼포먼스를 향상시키는데 도움을 줍니다. 초보 라이더 역시 얼마나 멀리, 빠르게 달렸는 지를 파악할 수 있어 효과적인 운동 목표를 설정할 수 있습니다.
High-sensitivity GPS receiver locates satellites quickly while ANT+, Bluetooth 4.0 and WLAN allow NeosTrack to connect to sensors and sync with smartphones or networks for quick uploads and firmware and GPS updates.
Connect to Dura-Ace and Ultegra Di2 systems for real-time on-screen gear ratios and combinations, along with Di2 battery levels. You can scroll through screens using Di2 shifter hood buttons.
Combine NeosTrack with popular ANT+ power meters to take your training to the next level. NeosTrack displays up to 10 valuable training power data points including left and right pedal balance and efficiency.
TrainSmart uses pre-programmed workouts to test and track physical condition and create customized intervals and workouts based on desired fitness results.
Create a new route from previous rides or upload gpx files directly to NeosTrack using the NeosTrack app, NeosTrack website or other popular mapping programs or websites.
NeosTrack provides turn-by-turn directions, allowing you to focus on the ride without worrying about where to go.
NeosTrack displays all ride data including ride time, route distance, average speed and elevation gains.
In most cases, a GPS signal should be acquired within 1 minute of turning on your Neostrack in an open environment. In some cases, it may take up to 5 minutes to find your current position. For instance:
The first time using Neostrack
Starting your Neostrack after a long period of not using.
If the Neostrack has been relocated without using it (such as after traveling by plane or train).
The Neostrack memory is mostly full. This can delay the start up procedure. Please delete unneeded ride history from the Neostrack and retry.
If it takes longer than 5 minutes to acquire a GPS signal, turn the device off, make sure that you are in an open area, without tall buildings or trees around you, then, retry turning the device on to restart the GPS signal search procedure.
Make sure the daylight-saving time is in the correct setting. Go to menu (Setup>System>Time/Unit> Dlight Save) and adjust the daylight saving setting per your time zone. When your Neostrack acquires a GPS signal, the time should set automatically.
Press the bottom button for 3 seconds to turn off the Neostrack. If the Neostrack does not turn off, hold the bottom and right-side buttons for a few seconds to reset your Neostrack (*note: resetting the device will delete all activities stored on the Neostrack device).
Make sure you have the correct wheel size dimension entered in your Neostrack. An incorrect wheel size can result in false speed and distance data displayed when using a speed sensor or Speed/Cadence sensor.
The Neostrack altitude function based on barometric pressure. The pressure sensor is covered by a Gore-Tex membrane that is water resistant but is not waterproof. Under certain circumstances (significant humidity or temperature changes) it is normal for the screen to become temporarily foggy due to extreme humidity/temperature changes. This condition should self-correct if power charge cap is left open and Neostrack is left screen-down overnight. If the screen does not return to normal within 24 hours, please contact your local Giant Bicycles retailer for assistance.
Please make sure your cell phone operating system software version update to Android 5.0 or newer or iOS version 8.0 or newer. Turn on GPS location service on phone and make sure Bluetooth on both the Neostrack and cell phone are turned on. Please also note you must do Bluetooth pairing in the Neostrack App not the Bluetooth settings in your phone. In urban areas (such as high-density apartment buildings) there can be a large number of Bluetooth devices present, which can cause interference. Please turn the Bluetooth function on your cell phone off and then on again (or turn the cell phone off and on again). Then retry uploading via Bluetooth.
For security, each Neostrack computer can only be paired and synced with one Neostrack App account. You may encounter issues due to your device being paired with different accounts. Signing up separately using Facebook, STRAVA™ and email will create multiple user accounts. Please ensure information is stored in only one account to avoid confusion, use only this account to log-in to the Neostrack App and website.
Please make sure you press the recording button before your ride. If the problem persists, reset your Neostrack and re-sync it with your Neostrack App.
Please make sure you have stopped recording you activity correctly before attempting to upload or sync your ride data. Not doing so can result in incomplete data files, which may not upload correctly. Please see the Neostrack Quick-Start Guide or Detailed User Manual for correct recording start/stop procedures.
You must upload data to Neostrack App first then auto sync to STRAVA™ or TrainingPeaks™. If you have already attempted a data sync without having the account paired and wish to still upload your ride data to STRAVA™/TrainingPeaks™, you can do so manually by connecting the device to your PC or Mac and uploading the .fit files directly on the STRAVA™/TrainingPeaks™ websites.
Turn off the GPS function and set up the speed sensor as the main speed source. Go to Menu (Setup>Bike Data>(if you have more than one bike, select the bike in question)>Speed source>Priority 1>Speed/CAD)
A Shimano D-Fly Management System is required to pair Shimano Di2 with Neostrack. You need to purchase and install a Shimano D-fly module for Bluetooth data to be transmitted by the Shimano Di2 group-set.
Ensure you are using the correct bike profile and that there is no other bikes within 5 meters when pairing. Go to menu (Setup>Bike Data>(if you have more than one bike, select the bike in question)>Sensors>Power or Di2)
Neostrack can be set up with a maximum of seven bike profiles; each bike profile can pair more than one sensor individually, therefore make sure to set the correct sensors to the right bike profile. Sensors being used across multiple bike profiles will need to be paired again with each new bike profile.
Ensure the sensor battery has enough power. If not, please replace with a new battery (noting correct battery orientation). If the sensor is brand new, remember to remove the protective battery tab before use.
Go to menu (Setup>Bike Data>(if you have more than one bike, select the bike in question)> Sensors
The Neostrack App has three ways to create an account via Facebook, STRAVA™, or e-mail. Please sync to only one and remember which account you are using.
Please note, if you already paired your device UUID with Facebook, you have to use Facebook to login. If you use your STRAVA™ account to login, it will not recognize the account you created using Facebook.
If you use an E-mail account to login and you forget your password, select the link “Forget Password” to reset your password. You will receive an email with your account information; please remember your Email login details to access the password reset.
If you cannot remember which login method your Neostrack app account uses to login or that is already paired with your device UUID. Please send an email to Giant and provide your device UUID. We will investigate and remove the account link for your device. Then, you need to create a new account and begin the account/device pairing process again.
Compatibility with all GPX files from a third-party source cannot be guaranteed. The Neostrack only supports the Neostrack App and Neostrack website when planning a route. GPX routes from third-party websites may not display at all or may display errors, such as turn by turn function, street naming, etc.